請問 HP ProLiant DL380 G3 的安裝問題

[Ruth]

請教各位先進, 在安裝完成 reboot 後, 出現以下訊息:
-------------------------------------------------------
*Remounting root filesystem read-only (if necessary)...[ok]
*Checking root filesystem...
ext2fs_check_if_mount: No such file or directory
while determine whether /dev/cciss/c0d0p6 is mounted.
fsck.ext3: No such file or directory while trying to open
/dev/cciss/c0d0p6 ...

以下是安裝的過程:
-------------------------------------------------------
HP ProLiant DL380 G3,
Xeon(DP) 2.4GHz CPU*2, RAM 512MB*2, HD 36GB*4
HP Smart Array 5i RAID controller (slot 0)

2004.3 Universal LiveCD, x86, stage3

fdisk /dev/cciss/c0d0
mke2fs /dev/cciss/c0d0p5 (for /boot)
mke2fs -j /dev/cciss/c0d0p6 (for /)
mkswap /dev/cciss/c0d0p7 (for swap)
mount /dev/cciss/c0d0p6 /mnt/gentoo
mount /dev/cciss/c0d0p5 /mnt/gentoo/boot
swapon /dev/cciss/c0d0p7
...(複製檔案)
mount -t proc proc /mnt/gentoo/proc
mount -o bind /dev /mnt/gentoo/dev
chroot /mnt/gentoo /bin/bash
env-update
source /etc/profile
emerge gs-source
核心設定如下:
processor type: Pentium 4, High Memory Support
(不知Xeon該選哪一個, 所以選Pentium4)
Multi-device support(RAID and LVM): 沒有選取
File System: EXT3, reiserfs, xfs 都選了
Network device support: Ethernet(1000Mbit support) --> Broadcom Tigon 3
Block devices: Compaq Smart Array5xxx Support
General Setup: PCI Hotplug Support --> Compaq PCI Hotplug driver
...(編譯核心)
emerge grub
nano -w /boot/grub/device.map
新增 (hd0) /dev/cciss/c0d0
grub --device-map /boot/grub/device.map
grub> root (hd0,4)
grub> setup --stage2=/boot/grub/stage2 (hd0)

-------------------------------------------------------
/etc/fstab
-------------------------------------------------------
/dev/cciss/c0d0p5 /boot ext2 noauto,noatime 1 1
/dev/cciss/c0d0p6 / ext3 noatime 0 0
/dev/cciss/c0d0p7 none swap sw 0 0

-------------------------------------------------------
/boot/grub/grub.conf
-------------------------------------------------------
timeout 10
default 0
fallback 1

title Gentoo-2.4.26-r9
root (hd0,4)
kernel (hd0,4)/kernel-2.4.26-gentoo-r9 root=/dev/cciss/c0d0p6

title MiniFedoraC1
root (hd0,0)
kernel /vmlinuz-2.4.22-1.2197.nptlsmp ro root=LABEL=/
initrd /initrd-2.4.22-1.2197.nptlsmp.img

因為在dmesg | grep cciss 所看到的是 /dev/cciss/host0/target0
所以嚐試將/etc/fstab修改為:
/dev/cciss/host0/target0/part5 /boot ext2 noauto,noatime 1 1
/dev/cciss/host0/target0/part6 / ext3 noatime 0 0
/dev/cciss/host0/target0/part7 none swap sw 0 0
但在 reboot 後, 結果仍然相同...

以上是安裝過程...anyone please help me...

[oai79]

有看過 嗎？好像手續有點額外的要處理。

[Ruth]

是的, 我已經先看過那篇討論的文章了, 大概的問題是出在安裝 grub 時,
會找不到 (hd0,0), 另外就是在 reboot 後, 硬碟的 name 會改變.
我加入的步驟有:

* mount -o bind /dev /mnt/gentoo/dev
* /boot/grub/device.map 中新增 (hd0) /dev/cciss/c0d0
* 修改 fstab 為: /dev/cciss/host0/target0/part*

或許還漏了一些重要的步驟, 但實在不知問題到底出在哪裡...
ps. 接觸 Gentoo 前都使用 windows, 如果問了一些 no sense 的問題, 還請大家原諒...

-Ruth

[orscar]

請問 HP ProLiant DL380 G3 安裝gentoo後.是否有硬體驅動程式可用.如可控制風扇轉速.

[oai79]

[Ruth]

設定 grub 時確實會有 Error21: Selected disk does not exit, 但後來參考原文 post 的解決方法已經OK了.
問題是在重開機後, 可以順利啟動 grub, 但進入 gentoo 時, gentoo似乎認不得 fstab 中所定義的 HD device(錯誤訊息如第一個 post).
Checking root filesystem時的Error: No such file or directory while trying to open /dev/cciss/c0d0p6
以下是 dmesg 及 lsmod 資訊.

------------------------------------------------------------------------
dmesg 的片段
------------------------------------------------------------------------
tg3.c:v3.10 (September 14, 2004)
eth0: Tigon3 [partno(TBD) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:0b:cd:3c:ff:9d
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth1: Tigon3 [partno(TBD) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:0b:cd:3c:ff:9c
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
HP CISS Driver (v 2.6.2)
cciss: Device 0xb178 has been found at bus 1 dev 3 func 0
cciss: using DAC cycles
blocks= 213367680 block_size= 512
heads= 255, sectors= 32, cylinders= 26148

/dev/cciss/host0/target0: p1 p2 p3 p4 < p5 p6 p7 >
fbsplash: console 11 using theme 'livecd-2004.3'

------------------------------------------------------------------------
lsmode
------------------------------------------------------------------------
Module Size Used by
ipv6 182560 16
evdev 6464 0
cciss 33636 0
tg3 65860 0
parport_pc 27072 0
parport 22728 1 parport_pc
sbp2 16744 0
ohci1394 24836 0
ieee1394 62008 2 sbp2,ohci1394
ohci_hcd 15044 0
uhci_hcd 23152 0
usb_storage 46208 0
ehci_hcd 21028 0

-Ruth

[oai79]

[Ruth]

[hpeter]